Profile

Nikhat Sayed

Student

Contact Details

Student
Work: (714) 548-4383

My Content

1 to 10 of 10 total

RE: Cartons that require Die-cutting

Posted By Nikhat Sayed 01-26-2026 11:08 PM
Found In Egroup: All Member Forum \ view thread
Hi Bethel, We give a bleed of around 3 mm to 4 mm; in some scenarios it is given up to 5 mm as well. The tolerances when the die board hits the sheet are considered to be anywhere between 2 pt and 4 pt mm. Tooling generally lasts for a million impressions, but the moment you see a ragged ...

RE: Brainpower needed: Liquid Paperboard Cartons issues ( Corner Tear)

Posted By Nikhat Sayed 12-31-2025 03:36 PM
Found In Egroup: All Member Forum \ view thread
Kyle pH 7 is neutral. anything below 7, the acidic level increases Thank you; I hope the carton manufacturer is able to resolve this issue. Happy New Year. 😊 ------------------------------ Nikhat Sayed Printing & Packaging Engineer Irvine CA (714) 548-4383 ...

RE: Brainpower needed: Liquid Paperboard Cartons issues ( Corner Tear)

Posted By Nikhat Sayed 12-24-2025 09:56 PM
Found In Egroup: All Member Forum \ view thread
Hi Kyle, Since this is meant to be a 6-ply structure, please check the PE layer thickness. If the PE is on the thinner side, it might be contributing to corner tears One possibility is that the dieboard tooling used to form the box may be creating very sharp or deep creases. I have a strong feeling ...

RE: Thoughts on Bio-based Packaging??

Posted By Nikhat Sayed 10-26-2025 08:11 PM
Found In Egroup: All Member Forum \ view thread
Hi Mayela, As I understand, you plan to replace the polyethylene (PE) layer currently used in paperboard takeout containers. There have been some scalability challenges associated with using seaweed film as a packaging material or laminate. However, it has shown good stability upon contact with ...

Epoxy Alternatives for ISO/OSHA/FDA Compliance in Packaging Warehouses

Posted By Nikhat Sayed 07-25-2025 01:08 AM
Found In Egroup: All Member Forum \ view thread
Hello Packaging Experts I have a question regarding warehouse compliance for storing printed flexible packaging materials. Is there an acceptable substitute for epoxy flooring that still meets the requirements for ISO, OSHA, and FDA compliance? I understand that epoxy coating is highly recommended ...

RE: Brown Box Strength and Pallet Efficiency

Posted By Nikhat Sayed 05-03-2025 03:41 PM
Found In Egroup: All Member Forum \ view thread
Hi Jacob, One effective solution is using HDPE pallets, which are lightweight, sustainable, and recyclable. These pallets are easy to carry, reducing logistical costs while being environmentally friendly. For the packaging itself, the choice of carton strength and design plays a key role. Depending ...

RE: Walmart RFID tag requirement for eCommerce item only

Posted By Nikhat Sayed 03-28-2025 02:09 AM
Found In Egroup: All Member Forum \ view thread
You are welcome Anthony ------------------------------ Nikhat Sayed Printing & Packaging Engineer Irvine CA (714) 548-4383 ------------------------------

RE: Walmart RFID tag requirement for eCommerce item only

Posted By Nikhat Sayed 03-25-2025 07:39 PM
Found In Egroup: All Member Forum \ view thread
Hey Anthony, Even if it is a seasonal product, it is important to have RFID to understand the stock in the Wallmart's Fulfillment Center, in case the products gets exhausted or becomes less it is important to have. The RFID system can then trigger an automated restock request. It also helps in doing ...

RE: Fragile industrial solution - advice needed

Posted By Nikhat Sayed 02-28-2025 06:50 PM
Found In Egroup: All Member Forum \ view thread
Hi Keli, Polyurethane for this should have a higher hardness of 80 to 90 Shore A, though the height of 25 cm is not that high but a higher density of 40-50 lbs/ft³ density range should be able to protect the 121 lbs product. A foam with a lesser compression will be able to protect the product. ...

RE: Plastic tubes - distribution methods when not cartoned

Posted By Nikhat Sayed 11-15-2024 02:32 PM
Found In Egroup: All Member Forum \ view thread
Hi Danielle, I understand your concern about removing the cartons from plastic tubes, which can help you reduce the carbon footprint. I know someone from my contact who can help you with this, will you be okay to connect on this through a call? Please do let me know. Regards, Nikhat ...